Aliner
|
protect your investment and save money
Aliner
|
NOTE: Some models of A frame campers (especially recent Aliner long-body Expeditions & long-body Ranger models) have the roof latches mounted at different locations on each side of the camper requiring a different kit. If your camper has this arrangement you will need the alternate Long-Body High Wind kit, which contains some additional hardware & different instructions.
|
no match for the big bad wolfHigh Wind KitOur High Wind Kit is a very cost-effective, preventative measure to minimize or eliminate wind damage to your Aliner investment!
All directions are included, our customers have been very satisfied with the quality of the stainless steel fasteners kit and the illustrated, easy-to-follow instructions. Two aluminum bars are needed BUT not included in our kit. These bars can be purchased at most Lowes, Home Depot, Ace Hardware or building supply outlets. WHEN ordering specify:
|
maximum protection from windA-Wall Pole KitCustomer of our highly successful A-frame High Wind Kit have requested we market a strong, portable pole kit to extend from one interior A-wall to the other. This kit provides maximum wind protection.
Designed to the same tough standards as our other kits, the "A-Wall Pole Kit" provides maximum security against high winds. Don’t be fooled – simple telescopic poles with friction twist locking will slide together under high winds. How hard do you think winds blow? Our design uses steel tubing and a steel locking pin to provide maximum safety. All directions are included in this kit along with fabricated pole-end assemblies & fasteners, you MUST purchase the thin-wall metal conduit at your local hardware store. If you buy conduit in the standard 10-foot length, you’ll have enough conduit left over to make an overhead shelf in the peak of the A-roof space, so grab an extra A-wall pole kit. |
If your Dometic 3-way refrigerator has two plastic doors that require removal for you to flip switches to change from 120-volt AC electric current (plug-in) to 12-volt DC electric current (battery) or LP power, then you must open and close these vent covers each time you change the power settings.
|
secure your doorFridge Vent Door KitOur kit provides secure latching of your exterior refrigerator vent doors. Eliminate the loss of your exterior vent doors due to weak or broken plastic clips. Also makes removal and replacement easy for your hands. Our stainless steel, nickel-plated and treated steel parts mean the highest quality come with easy-to follow directions (no drilling needed, just screw together).
|
don't lose your doorWater Heater Door LatchThe original, factory-installed water heater door latch has a plastic latch-handle and is prone to failure due age, and exposure to the elements. Once broken, the door could fall off while driving.
Our Water Heater Door Latch kit includes parts made of stainless steel, nickel-plated steel or rust-resistant spring steel. Our fasteners hold the water heater door firmly in place and make it easier to open the door when compared to the original plastic latch. This easy-to-install kit requires only simple household pliers and installs in minutes with no drilling. |
Thin Skin Pop Rivets work with any pop rivet gun capable of handling a 3/16” diameter pop rivet. They can hold items weighing up to 2 pounds on the exterior of your camper.
|
lightweight fastenersThin Skin Pop RivetsWe like to make functional “mods” (modifications) to our A-frame trailer, but I had problems finding a way to fasten lightweight items (latches, hardware, etc.) to the outer "skin” of my trailer.
I discovered these special pop rivets that work great on both interior & exterior surfaces of trailers made of laminated metal/fiberglass+foam board+interior paneling. The ‘thin-skin rivets’ have three legs that spread out almost like those popular wall anchors. 10 rivets come in each package. These rivets can't be purchased in any local hardware stores. |
protect your wiringStainless Steel Wings Nuts
|
NOTE: You need to measure the diameter of the threaded terminals prior to ordering. They might both be 5/16 inches OR 3/8 inches OR one of each size depending on brand of battery. Please tell us what you need in your order email.
|